How do you make a ski shot board?

How to Make a Shotski

  1. Tools.
  2. Step 1: Get Your Supplies in Order. Get yourself an old, wood-core ski—the longer the better.
  3. Step 2: Measure and Mark.
  4. Step 3: Drill Some Shot Glass Nooks.
  5. Step 4: Personalize Your Shotski (Optional)
  6. Step 5: Stick on Some Shot Glasses.
  7. Step 6: Wait, Then Shoot!

How do you make a shot ski with old skis?

How To Make It

  1. Step 1: Measure the Base. With your donor ski on the ground, measure the ski from the forward base contact point to the rear base contact point.
  2. Step 2: Mark the Shot Glass Placements.
  3. Step 3: Drill it.
  4. Step 4: Add the Shot Glasses.
  5. Step 5: Wait.
  6. Step 6: Party.

What are the dimensions of a shot ski?

Standard Shot Ski Our most popular shot ski, with dimensions of 56″ long and 4″ wide. It comes standard with up to 4 shot glass holders. The shot glass holes are machined out of the laminated ski with a rubber grommet permamently affixed. A standard 1.75 oz shot glass fits nice and snug.

How do you make a magnet shot ski?

  1. What you’ll need. Glue.
  2. Choose the Base. A Shot Ski starts with a ski.
  3. Mark Where the Shot Glasses Go. The first step is to mark where the shot glasses will go.
  4. Drill Baby, Drill. It’s time to drill holes.
  5. Glue in your Magnets.
  6. Create Magnetic Shot Glasses.
  7. Test it out.

What is a Shotski board?

A “shotski,” as it’s called, involves several shot glasses placed equidistant apart across the deck of a discarded downhill ski, allowing several folks to concurrently down a shot. Shotskis are the sizzling fajitas of the barroom—you can’t help but notice when someone orders one.

Who invented the shot ski?

The origin of the shotski is unknown – though some say it began in Norway where skis were invented, while others say it was invented in Austria, where it’s known as the schnappski. One source almost tracked down its origins with the University of British Columbia’s ski steam.

Do it yourself ski shot?

Removable glasses Cut a piece of Velcro to fit inside the hole, and glue it to the ski. Glue the other side of the Velcro to the base of a shot glass. Repeat with remaining shot glasses. The result will be less sturdy than the first option, but the shot glasses will be removable for easy cleaning and storage.

How far apart should shots be on a Shotski?

approximately 18 – 20 inches apart
Ideally, shots are approximately 18 – 20 inches apart, enough room for folks to face the shot ski head on. Make marks that are centered in the ski width-wise and get ready to drill.

How do you hang a shot ski on the wall?

A 3 step guide to hanging your shot ski on the wall:

  1. Line up the ski where you want it on the wall and mark the spot at the top of the highest hole.
  2. Bang a nail in the wall where you marked the spot (we like the darker nails as they look a little nicer)
  3. Plonk your ski up on the nail – job done!

Are mini skis easier?

You’re a beginner skier – shorter skis tend to be easier to control. You’re getting older and your strength, fitness, and reflex speed is not what it once was – you’ll benefit from shorter skis. You prefer to ski at a slower speed. You’re not as an aggressive skier.

What is the point of Shotski?

The idea behind the shotski is simple. It’s a ski with either three, four, or five shot glasses attached to it. Brave drinkers afraid to sip alone hold the ski together, lift it like a portable miniature table to their faces, and, like one multi-body drinking machine, down every last drop of liquor in the shot glasses.

What is a Shotsky?

How do you make a shot ski?

While the magnets are drying, grab four shot glasses, the glue gun and the four washers. 2. Flip the shot glasses upside down. Place a dab of hot glue on the bottom of the glasses and press the washers down until set. 3. Let the glue dry. 4. Once dry, set each shot glass onto a magnet to assemble your shot ski. 5.

How do you attach a shot glass to a shotski?

For a shotski with removeable glasses: Cut a piece of velcro to fit inside the hole, and adhere it to the ski with the glue. Adhere the other side of the velcro to the base of a shot glass. Repeat with remaining shot glasses.

How do you make a bottle holder for a ski?

Strip a ski of its binding and lay it flat on a solid surface. Cut off the tip and tail about 2 ft. from either end. 2. Over a piece of scrap wood, drill three evenly spaced holes all the way through the ski tip section. This will hold the bottles. 3.

How do you build a ski rack?

Building a ski rack is surprisingly easy, and it’ll save you money in the long run. Choose a location for your ski rack. You’ll need a space that’s as wide as your skis/snowboards are long. The height will depend on how many skis/snowboards you have; the more pegs needed, the taller the rack.