How do I get rid of virtual chassis configuration?

How do I get rid of virtual chassis configuration?

To delete an MX Series Virtual Chassis configuration, you must:

1. Delete all Virtual Chassis ports.
2. Remove the definitions and applications of the Virtual Chassis configuration groups.
3. Delete the preprovisioned member information configured at the [edit virtual-chassis] hierarchy level.
4. Delete any configured interfaces.

What is virtual chassis in Juniper?

Virtual Chassis Basics on Switches. Virtual Chassis is a feature on Juniper Networks routing or switching devices that provides network resiliency in the form of redundant Routing Engines and network expansion flexibility with minimal impact to a configuration.

How do I configure a Juniper switch?

To connect and configure the switch from the console by using the CLI:

1. Connect the console port to a laptop or PC by using the RJ-45 to DB-9 serial port adapter.
2. At the Junos OS shell prompt root% , type ezsetup .
3. Enter the hostname.
4. Enter the root password you want to use for the device.

How do you remove the switch from a virtual chassis Juniper?

To remove a switch from a Virtual Chassis without replacing it:

1. Power off and disconnect the member switch you want to remove from the Virtual Chassis.
2. If the Virtual Chassis configuration is preprovisioned, on the Virtual Chassis primary, remove the removed switch’s member setting from the preprovisioned configuration.

What are two benefits of the Virtual Chassis fabric VCF technology?

VCF allows customers that have maximized the port capacity of a Virtual Chassis to expand it without having to remove the existing, previously- purchased devices of that Virtual Chassis. It supports data centers that contain a mix of 1-Gbps, 10-Gbps, and 40-Gbps Ethernet interfaces.

What is VCP in Juniper switch?

A Virtual Chassis port (VCP) in an EX8200 Virtual Chassis is any port whose function is to send and receive Virtual Chassis Control Protocol (VCCP) traffic to create, monitor, and maintain the Virtual Chassis.

How do I find my interface configuration in Juniper?

To display the current configuration for a Juniper Networks device, use the show command in configuration mode. This command displays the configuration at the current hierarchy level or at the specified level.

How do I set the management IP on a Juniper switch?

To configure a management port by CLI commands.

1. Use the command “family inet address” to configure a management IP address on the interface.
2. Configure a static route with the next hop to the management network default gateway set routing-options static route 0.0.0.0/0 next-hop 10.93.15.1/21.

Which three configuration elements are considered part of the initial configuration?

Which three configuration elements are considered part of the initial configuration? ( Choose three.)

• hostname.
• root password.

How do I enable logical interface in Juniper?

In configuration mode, go to the [edit interfaces interface-name unit logical-unit-number ] or [edit logical-systems logical-system-name interfaces interface-name unit logical-unit-number ] hierarchy level. Configure the encapsulation type as described in encapsulation (Logical Interface).

What is no split detection?

If you have only two members in your Virtual Chassis, we strongly recommend that you configure no-split-detection to disable the split and merge feature. This feature makes sure both switches remain in the correct Virtual Chassis roles in the event of a Virtual Chassis split.

How do I configure the Virtual Chassis on the ex4300 switches?

You must configure the Virtual Chassis into mixed mode. You must also include a special port mode option ( ieee-clause-82 ) when you configure mixed mode on the EX4300 switches that are not multigigabit models.

Is my config improper on the ex4300?

Eagular, been following this thread. I believe your config, at least on the EX side is improper. On the EX4300 none of the interfaces should be members of an AE, they should all be single links. The Reth config on the SRXs takes care of making sure traffic goes across the proper links.

How do I configure the Virtual Chassis?

You can configure the Virtual Chassis using either of the following options: A nonprovisioned configuration—The primary sequentially assigns a member ID to other member switches. The role is determined by the primary-role priority value and other factors in the primary-role election algorithm.