How do I access Polycom web GUI?

You can access the Polycom Web Configuration Utility using any compatible web browser installed on your PC.

  1. Power on the phone.
  2. Confirm that the PC and phone are on the network.
  3. Enter phone’s IP address into your supported web browser.
  4. For Username, enter: Polycom.
  5. For Password, enter: 456.

How do I set up my Polycom Internet phone?

Connect Your Polycom Phone

  1. Locate the LAN and PC ethernet ports on the bottom of the phone.
  2. Connect the ethernet cable for your network into the LAN port.
  3. Connect an ethernet cable from your computer or laptop dock/port replicator to PC port, if applicable.
  4. Complete the setup process:

What is the Polycom provisioning server address?

The default is 456. 2 Choose Admin Settings > Network Configuration > Provisioning Server, and press the Select soft key.

How do I reprovision my Polycom phone?

Factory Reset and Provisioning On The Physical Phone

  1. On the phone, press the Menu key.
  2. Select the Settings option.
  3. Select the Advanced option.
  4. Enter the password 456 and press the Enter softkey.
  5. Select Admin Settings.
  6. Select Restore to Defaults.
  7. Select Reset to Factory.

How do I manually configure a Polycom phone via web interface?

Once logged into the Polycom phone’s web UI go to the Lines section at the top -> Line 1 and fill out the following fields as follows:

  1. Display Name: SIP Extension Number.
  2. Address: SIP Extension Number.
  3. Authentication User ID: SIP Extension Number.

How do I enable Web interface on Polycom VVX?

On the Desk Phone interface go to the option >> “Menu Key” >> Select Settings>>Advanced >> login with the password 456 >>> admin settings >>>web server >>> enable http and/or https. Hope this helps!

How do I enable URL on my Polycom phone?

Troubleshooting the “URL Calling is Disabled” Message on a Poly® VVX Phone

  1. Press the Home. button on the Poly device.
  2. Use the 5-Way Navigation Key to navigate to Settings > Status > Network > TCP/IP Parameters.
  3. Verify that the phone has an IPv4 address assigned to it. If so, continue troubleshooting.

How do I connect my Polycom to WIFI?

You can enable wireless connectivity for your USB-enabled VVX phone using the Polycom® Wi-Fi wireless network adapter….Prerequisite:

  1. Insert the Polycom Wi-Fi wireless network adapter into the USB port of your VVX phone.
  2. Go to Settings > Basic > Wi-Fi.
  3. Select Wi-Fi, then select On.
  4. Select Yes to reboot the phone.

How do I create a provisioning server on Polycom?

Configuring the provisioning server via the Polycom web interface:

  1. Open the Web Interface of the Polycom device and “Login As Admin” (default password is 456).
  2. Navigate to “Settings” -> “Provisioning Server.”
  3. Set “Server Type” to HTTP.
  4. In “Server Address” enter the provisioning URL taken in step 1.

What is the password for Polycom Web Configuration Utility?

The default User password is: 123. To access the Web Utility: 1 Launch a compatible Web browser from your PC and enter the IP address of the phone you wish to configure into the address bar.

How do I enable url calling?

Go to Menu > Status > Network > TCP/IP Parameters > IP. Confirm DHCP is enabled. If the phone is not showing an IP address, restart your phone. After restarting your phone and there is still no IP address, check the router’s DHCP settings to see if there are enough IP addresses in the pool.

Why is URL calling disabled Polycom?

URL Call Disabled is a Phone Registration Error experienced by Polycom phones. This happens when there is a network issue. When the Softswitch or Software Switch is unable to link PSTN to IP Networks, the “URL Call Disabled” error is displayed on your Polycom phone.